Introduction
Development Kit
| IP Core | IP Core Category |
|---|---|
| altera_jtag_avalon_master | QsysInterconnect |
| Avalon-ST Bytes to Packets Converter | QsysInterconnect |
| Avalon-ST Channel Adapter | QsysInterconnect |
| Avalon-ST Single Clock FIFO | QsysInterconnect |
| Avalon-ST JTAG Interface | QsysInterconnect |
| Avalon-ST Packets to Bytes Converter | QsysInterconnect |
| Reset Controller | QsysInterconnect |
| Avalon-ST Timing Adapter | QsysInterconnect |
| Avalon Packets to Transaction Converter | QsysInterconnect |
| Avalon-MM Master Translator | QsysInterconnect |
| Avalon-MM Clock Crossing Bridge | QsysInterconnect |
| MM Interconnect | QsysInterconnect |
| Avalon-ST Adapter | QsysInterconnect |
| Avalon-ST Error Adapter | QsysInterconnect |
| Memory-Mapped Demultiplexer | QsysInterconnect |
| Memory-Mapped Multiplexer | QsysInterconnect |
| Avalon-MM Master Agent | QsysInterconnect |
| Avalon-MM Slave Agent | QsysInterconnect |
| Avalon-MM Slave Translator | QsysInterconnect |
| Memory-Mapped Router | QsysInterconnect |
| Memory-Mapped Traffic Limiter | QsysInterconnect |
| SPI (3 Wire Serial) | SPI |
| Low Latency Ethernet 10G MAC | Ethernet |
| Arria 10 1G/10GbE and 10GBASE-KR PHY | Ethernet |
| Arria 10 Transceiver Native PHY | TransceiverPHY |
| Transceiver PHY Reset Controller | TransceiverPHY |
| Altera IOPLL | ClocksPLLsResets |
| Arria 10 Transceiver ATX PLL | TransceiverPLL |
| Arria 10 FPLL | ClocksPLLsResets |
| Altera Arria 10 XCVR Reset Sequencer | Other |
| Altera In-System Sources & Probes | SimulationDebugVerification |
Detailed Description
Prepare the design template in the Quartus Prime software GUI (version 14.1 and later)
Note: After downloading the design example, you must prepare the design template. The file you downloaded is of the form of a <project>.par file which contains a compressed version of your design files (similar to a .qar file) and metadata describing the project. The combination of this information is what constitutes a <project>.par file. In releases 16.0 or newer, you can simply double click on the <project>.par file and Quartus will launch that project.
The second means to bring up the project template is through the New Project Wizard (File -> New Project Wizard). After entering the project name and folder on the first panel, the second panel will ask you to specify an empty project or project template. Select project template. You will see a list of Design Templates projects that you have loaded prior as well as various "Baseline Pinout Designs" that contain the pinout and settings for a variety of development kits. If you don't see your design template in the list, click on the link that states install the Design Templates circled below:
Browse to the <project>.par file you downloaded, click next, followed by Finish, and your design template will be installed and displayed in the Project Navigator pane in Quartus.
Note: When a design is stored in the Design Store as a design template, it has been previously regression tested against the stated version of Quartus software. The regression ensures the design template passes analysis/synthesis/fitting/assembly steps in the Quartus design flow.
Prepare the design template in the Quartus Prime software command-line
At the command-line, type the following command:
quartus_sh --platform_install -package <project directory>/<project>.par
Once the process completes, then type:
quartus_sh --platform -name <project>
Note:
* ACDS Version: 16.1.0 Standard