GTS JESD204C Intel® FPGA IP User Guide

Download PDF
ID 813959
Date 5/09/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the GTS JESD204C Intel® FPGA IP User Guide 2. Overview of the GTS JESD204C Intel® FPGA IP 3. Functional Description 4. Getting Started 5. Designing with the GTS JESD204C Intel® FPGA IP 6. GTS JESD204C Intel® FPGA IP Parameters 7. Interface Signals 8. Control and Status Registers 9. Document Revision History for the GTS JESD204C Intel® FPGA IP User Guide
2. Overview of the GTS JESD204C Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. GTS JESD204C Intel® FPGA IP Features 2.4. Performance and Resource Utilization
3. Functional Description x
3.1. Clocks 3.2. Local Extended Multiblock Clock 3.3. CRC Encoding/Decoding 3.4. Scrambler/Descrambler
3.1. Clocks x
3.1.1. Device Clock 3.1.2. Frame Clock and Link Clock 3.1.3. GTS Reset Sequencer Intel® FPGA IP Clock
3.2. Local Extended Multiblock Clock x
3.2.1. LEMC Counter
4. Getting Started x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Intel® FPGA IP Evaluation Mode 4.3. IP Catalog and Parameter Editor 4.4. GTS JESD204C IP Component Files 4.5. Creating a New Quartus® Prime Project 4.6. Parameterizing and Generating the IP 4.7. Compiling the GTS JESD204C IP Design 4.8. Programming an FPGA Device
5. Designing with the GTS JESD204C Intel® FPGA IP x
5.1. Configuring the GTS Reset Sequencer Intel® FPGA IP 5.2. Reset Initialization 5.3. Configuration Phase 5.4. Link Reinitialization 5.5. SYSREF Sampling 5.6. Interrupt and Error Handling 5.7. Multi-Device Synchronization 5.8. Deterministic Latency 5.9. Pin Assignments 5.10. Dual Simplex Support 5.11. Analog Parameter Settings 5.12. Transceiver Toolkit
5.2. Reset Initialization x
5.2.1. GTS JESD204C TX Reset Sequence 5.2.2. GTS JESD204C RX Reset Sequence
5.6. Interrupt and Error Handling x
5.6.1. Interrupt Configuration for TX and RX 5.6.2. Interrupt Top Half ISR Handler 5.6.3. Interrupt Bottom Half ISR Handler
5.7. Multi-Device Synchronization x
5.7.1. Multi-Device DAC Application for Subclass 1 5.7.2. Multi-Device ADC Application for Subclass 1
5.8. Deterministic Latency x
5.8.1. RBD Tuning Mechanism
7. Interface Signals x
7.1. Transmitter Signals 7.2. Receiver Signals
8. Control and Status Registers x
8.1. Transmitter Registers 8.2. Receiver Registers
1. About the GTS JESD204C Intel® FPGA IP User Guide
2. Overview of the GTS JESD204C Intel® FPGA IP
3. Functional Description
4. Getting Started
5. Designing with the GTS JESD204C Intel® FPGA IP
6. GTS JESD204C Intel® FPGA IP Parameters
7. Interface Signals
8. Control and Status Registers
9. Document Revision History for the GTS JESD204C Intel® FPGA IP User Guide

8. Control and Status Registers

The control and status registers refer to byte addressing as seen by the software, and as implemented by hardware. All registers that are Read-Writable must be protected to comply with Security Development Lifecycle (SDL) practices. You are required to perform the register access protection.
Table 21.  Register Access Type and DefinitionThis table describes the register access type for Intel® FPGA IPs.
Access Type Definition
RO Software read-only (no effect on write). The value is hard-tied internally to either '0' or '1' and does not vary.
RO/V Software read-only (no effect on write). The value may vary.
RC
  • Software reads and returns the current bit value, then the bit self-clears to 0.
  • Software read also causes the bit value to be cleared to 0.
RW
  • Software reads and returns the current bit value.
  • Software writes and sets the bit to the desired value.
RW1C
  • Software reads and returns the current bit value.
  • Software writes 0 and has no effect.
  • Software writes 1 and clears the bit to 0 if the bit has been set to 1 by hardware.
  • Hardware sets the bit to 1.
  • Software clear has higher priority than hardware set.
RW1S
  • Software reads and returns the current bit value.
  • Software writes 0 and has no effect.
  • Software writes 1 and sets the bit to 1.
  • Hardware clears the bit to 0 if the bit has been set to 1 by software.
  • Software set has higher priority than hardware clear.

Section Content
Transmitter Registers
Receiver Registers

Level Two Title