Stratix® 10 10GBASE-KR PHY IP Core User Guide

Download PDF
ID 683500
Date 4/09/2024
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the Stratix® 10 10GBASE-KR PHY IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Stratix® 10 10GBASE-KR PHY Registers 6. Interface Signals 7. Design Example 8. Supported Tools A. Difference between Stratix® 10 and Arria® 10 IP Variants B. Stratix® 10 10GBASE-KR PHY IP Core User Guide Archives C. Document Revision History for Stratix® 10 10GBASE-KR PHY IP Core User Guide
1. About the Stratix® 10 10GBASE-KR PHY IP Core x
1.1. Stratix® 10 10GBASE-KR PHY IP Core Supported Features 1.2. Device Family Support 1.3. IP Core Speed Grade Support 1.4. Resource Utilization 1.5. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IPs 2.2. Specifying the IP Core Parameters and Options 2.3. Generated File Structure 2.4. Simulating the IP Core 2.5. Integrating Your IP Core in Your Design 2.6. Stratix® 10 10GBASE-KR IP Core Testbench 2.7. Compiling the Full design
2.1. Installing and Licensing Intel® FPGA IPs x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Integrating Your IP Core in Your Design x
2.5.1. Pin Assignments 2.5.2. Adding the Transceiver PLL 2.5.3. Adding the fPLL 2.5.4. Adding the Stratix® 10 Transceiver PHY Reset Controller 2.5.5. Placement Settings for the Stratix® 10 10GBASE-KR PHY IP Core
5. Stratix® 10 10GBASE-KR PHY Registers x
5.1. Register Map 5.2. Register Definitions
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Data Interface Signals 6.3. Serial Data Signals 6.4. Avalon® -MM Interface Signals 6.5. Transceiver Reconfiguration Signals 6.6. Control and Status Signals
6.2. Data Interface Signals x
6.2.1. XGMII Mapping to Standard SDR XGMII Data
7. Design Example x
7.1. Quick Start Guide 7.2. Design Example Description
7.1. Quick Start Guide x
7.1.1. Design Example Directory Structure 7.1.2. Hardware Design Example Components 7.1.3. Simulation Design Example Components 7.1.4. Generating the Design Example 7.1.5. Simulating the Stratix® 10 10GBASE-KR Design Example Testbench 7.1.6. Compiling and Configuring the Design Example in Hardware 7.1.7. Testing the Hardware Design Example
7.2. Design Example Description x
7.2.1. Hardware and Software Requirements 7.2.2. Design Example Behavior 7.2.3. Design Example Interface Signals 7.2.4. Stratix® 10 10GBASE-KR PHY Design Example Registers
8. Supported Tools x
8.1. Ethernet Toolkit Overview
8.1. Ethernet Toolkit Overview x
8.1.1. Features
1. About the Stratix® 10 10GBASE-KR PHY IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Stratix® 10 10GBASE-KR PHY Registers
6. Interface Signals
7. Design Example
8. Supported Tools
A. Difference between Stratix® 10 and Arria® 10 IP Variants
B. Stratix® 10 10GBASE-KR PHY IP Core User Guide Archives
C. Document Revision History for Stratix® 10 10GBASE-KR PHY IP Core User Guide

7.1.6. Compiling and Configuring the Design Example in Hardware

To compile the hardware design example and configure it on your Stratix® 10 device, follow these steps:
  1. Ensure hardware design example generation is complete.
  2. In the Quartus® Prime Pro Edition software, open the Quartus® Prime project <design_example_dir>/hardware_test_design/de_wrapper.qpf.
  3. On the Processing menu, click Start Compilation.
  4. After you generate a SRAM object file (.sof), follow these steps to program the hardware design example on the Stratix® 10 device:
    1. On the Tools menu, click Programmer.
    2. In the Programmer, click Hardware Setup.
    3. Select a programming device.
    4. Select and add the Stratix® 10 Transceiver Signal Integrity Development Kit to your Quartus® Prime session.
    5. Ensure that Mode is set to JTAG.
    6. Select the Stratix® 10 device and click Add Device. The Programmer displays a block diagram of the connections between the devices on your board.
    7. In the row with your .sof, check the box for the .sof.
    8. Check the box in Program/Configure column.
    9. Click Start.
Related Information
Level Two Title