System Memory for Intel® Desktop Board DH61AG





System memory features
Supported memory configurations
Tested memory

System memory features

The board has two 204-pin SO-DIMM sockets and supports the following memory features:

  • 1.5V DDR3 SDRAM SO-DIMMs with gold-plated contacts
  • Support for 1.35V low voltage DDR3 (new JEDEC specification)
  • Two independent memory channels with interleaved mode support
  • Unbuffered, single-sided or double-sided SO-DIMMs
  • 16 GB maximum total system memory (with 4 Gb memory technology)
  • Minimum recommended total system memory: 1024 MB
  • Non-ECC SO-DIMMs
  • Serial presence detect
  • XMP profile support for voltage detection
  • DDR3 1333 MHz and DDR3 1066 MHz SDRAM SO-DIMMs

To be fully compliant with all applicable DDR SDRAM memory specifications, the board should be populated with SO-DIMMs that support the serial presence detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability may be impacted or the SO-DIMMs may not function under the determined frequency.

1.5V is the recommended and default setting for DDR3 memory voltage. The other memory voltage settings in the BIOS Setup program are provided for performance tuning purposes only. Altering the memory voltage may (i) reduce system stability and the useful life of the system, memory, and processor; (ii) cause the processor and other system components to fail; (iii) cause reductions in system performance; (iv) cause additional heat or other damage; and (v) affect system data integrity.

Intel has not tested and does not warranty the operation of the processor beyond its specifications. For information on the processor warranty, refer to Processor Warranty Information.

Supported memory configurations

Raw Card Version SO-DIMM Capacity DRAM Device Technology DRAM Organization # of DRAM Devices
A 1 GB 1 Gb 64 M x 16 8
2 GB 2 Gb 128 M x 16 8
B 1 GB 1 Gb 128 M x 8 8
2 GB 2 Gb 256 M x 8 8
C 512 MB 1 Gb 64 M x 16 4
1 GB 2 Gb 128 M x 16 4
F 2 GB 1 Gb 128 M x 8 16
4 GB 2 Gb 256 M x 8 16
8 GB 4 Gb 512 M x 8 16

Tested memory

Computer Memory Test Labs* (CMTL) tests third-party memory for compatibility with Intel® boards as requested by memory manufacturers. See the CMTL tested memory list* for this Intel® Desktop Board.

The table below lists parts which passed testing during development. These part numbers may not be readily available throughout the product life cycle.

Module manufacturer Module part number Module size Module speed (MHz)
Elpida EBJ21UE8BDS0-DJ-F/5 2 GB 1333
Elpida EBJ10UE8BDS0-DJ 1 GB 1333
Hynix HMT112S6TFR8C-H9/57 1 GB 1333
Hynix 204P HMT351S6BFR8C-H9/57 4 GB 1333
Hynix HMT125S6TFR8C-H9 2 GB 1333
Kingston HP572293-C01-ELDWG 2 GB 1333
Kingston KHX1600C9S3P1K2/8G 4 GB 1600
Micron MT16JTF25664HZ-1G4G 2 GB 1333
Micron MT8JTF12864HZ 1 GB 1333
Qimonda MT16JSF51264HZ-1G4D1 4 GB 1333
Samsung M471B2873GB0-CH9/57 1 GB 1333
Samsung M471B5273DH0 4 GB 1333
Samsung M471B5673GB0 2 GB 1333
Samsung SM471B2873GB0-CK0 S1 GB S1600
Samsung SM471B5773DH0-CK0 S2 GB S1600
Sanmax SMD-N2G88H3P 2 GB 1066
Sanmax SMD-N4G68HP 4 GB 1066