CPRI IP User Guide

Download PDF
ID 683595
Date 6/13/2025
Public
Document Table of Contents
Document Table of Contents x
1. About the CPRI IP 2. Getting Started with the CPRI IP 3. CPRI IP Functional Description 4. CPRI IP Signals 5. CPRI IP Registers 6. CPRI Altera® FPGA IP User Guide Archives 7. Document Revision History for the CPRI IP User Guide
1. About the CPRI IP x
1.1. CPRI IP Features 1.2. CPRI IP Device Family and Speed Grade Support 1.3. IP Verification 1.4. Resource Utilization for CPRI IP 1.5. CPRI IP Release Information
1.2. CPRI IP Device Family and Speed Grade Support x
1.2.1. CPRI IP Device Family Support 1.2.2. CPRI IP Device and Transceiver Speed Grade Support
2. Getting Started with the CPRI IP x
2.1. Installation and Licensing 2.2. Generating a CPRI IP 2.3. CPRI IP Parameters 2.4. Integrating the CPRI IP into your Design: Required External Blocks 2.5. Simulating Intel FPGA IP Cores 2.6. Running the CPRI IP Design Example 2.7. CPRI IP Design Example Clocks 2.8. About the Testbench 2.9. Compiling the Full Design and Programming the FPGA
2.1. Installation and Licensing x
2.1.1. Intel FPGA IP Evaluation Mode
2.2. Generating a CPRI IP x
2.2.1. CPRI IP Generated Files
2.4. Integrating the CPRI IP into your Design: Required External Blocks x
2.4.1. Adding the Transceiver TX PLL IP 2.4.2. Adding the Reset Controller 2.4.3. Adding the Transceiver Reconfiguration Controller 2.4.4. Adding the Off-Chip Clean-Up PLL 2.4.5. Adding and Connecting the Single-Trip Delay Calibration Blocks 2.4.6. CPRI IP Transceiver PLL Calibration 2.4.7. Reference and System PLL Clock for your IP Design
2.4.7. Reference and System PLL Clock for your IP Design x
2.4.7.1. System PLL Connections for the Agilex® 7 F-tile Variations 2.4.7.2. System PLL Connections for the Agilex 5 Variations 2.4.7.3. Reset Sequencer Connections for the Agilex 5 Variations
3. CPRI IP Functional Description x
3.1. Interfaces Overview 3.2. CPRI IP Clocking Structure 3.3. CPRI IP Reset Requirements 3.4. Start-Up Sequence Following Reset 3.5. AUX Interface 3.6. Direct IQ Interface 3.7. Ctrl_AxC Interface 3.8. Direct Vendor Specific Access Interface 3.9. Real-Time Vendor Specific Interface 3.10. Direct HDLC Serial Interface 3.11. Direct L1 Control and Status Interface 3.12. L1 Debug Interface 3.13. Media Independent Interface (MII) to External Ethernet Block 3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block 3.15. CPU Interface to CPRI IP Registers 3.16. Auto-Rate Negotiation 3.17. Extended Delay Measurement 3.18. CPRI IP Deterministic Latency 3.19. CPRI IP Transceiver and Transceiver Management Interfaces 3.20. Testing Features
3.2. CPRI IP Clocking Structure x
3.2.1. Example CPRI IP Clock Connections in Different Clocking Modes
3.4. Start-Up Sequence Following Reset x
3.4.1. Start-Up Sequence Interface Signals
3.5. AUX Interface x
3.5.1. AUX Interface Signals 3.5.2. AUX Interface Synchronization 3.5.3. Auxiliary Latency Cycles 3.5.4. Direct Interface CPRI Frame Data Format
3.14. Gigabit Media Independent Interface (GMII) to External Ethernet Block x
3.14.1. GMII Normal Mode 3.14.2. Ethernet PCS Bypass Mode 3.14.3. Ethernet PCS Run-Time Switching
3.15. CPU Interface to CPRI IP Registers x
3.15.1. CPU Interface Signals 3.15.2. Accessing the Hyperframe Control Words
3.15.2. Accessing the Hyperframe Control Words x
3.15.2.1. Specifying the Control Word 3.15.2.2. Specifying the Position in the Control Word 3.15.2.3. Retrieving the Hyperframe Control Words 3.15.2.4. Writing the Hyperframe Control Words
3.17. Extended Delay Measurement x
3.17.1. Extended Delay Measurement for Soft Internal Buffers 3.17.2. Extended Delay Measurement for Stratix® 10 Hard FIFOs 3.17.3. Extended Delay Measurement Interface
3.19. CPRI IP Transceiver and Transceiver Management Interfaces x
3.19.1. CPRI Link 3.19.2. Main Transceiver Clock and Reset Signals 3.19.3. Arria V, Arria V GZ, Cyclone V, and Stratix V Transceiver Reconfiguration Interface 3.19.4. Arria® 10, Stratix® 10, and Agilex® 7 Transceiver Reconfiguration Interface 3.19.5. RS-FEC Interface 3.19.6. Interface to the External Reset Controller 3.19.7. Interface to the External PLL 3.19.8. Transceiver Debug Interface
3.20. Testing Features x
3.20.1. CPRI IP Loopback Modes 3.20.2. CPRI IP Self-Synchronization Feature
4. CPRI IP Signals x
4.1. CPRI IP Core L2 Interface 4.2. CPRI IP Core L1 Direct Access Interfaces 4.3. CPRI IP Core Management Interfaces 4.4. CPRI IP Core Transceiver and Transceiver Management Signals
1. About the CPRI IP
2. Getting Started with the CPRI IP
3. CPRI IP Functional Description
4. CPRI IP Signals
5. CPRI IP Registers
6. CPRI Altera® FPGA IP User Guide Archives
7. Document Revision History for the CPRI IP User Guide

3.19.2. Main Transceiver Clock and Reset Signals

Table 46.  Main Transceiver Clock and Reset-Done SignalsThe clocks for individual interfaces are listed with the relevant interface signals.

Signal Name

Direction

Description

xcvr_cdr_refclk Input Receiver CDR reference clock. You must drive this clock at the frequency you specified for the Receiver CDR reference clock frequency (MHz) parameter in the CPRI parameter editor.

For the list of CDR frequency available based on line bit rate, refer to CPRI IP Parameters.

This signal is not present in IP core variations that target an Stratix® 10 E-tile and Agilex® 7 E- tile device.

xcvr_recovered_clk Output Direct recovered clock from the receiver CDR. Use this output clock to drive the external clean-up PLL when your IP core is in slave mode. This clock is present only in CPRI IP cores in slave clocking mode with Operation mode set to the value of RX/TX Duplex or RX Simplex.
xcvr_reset_tx_done Output Indicates the transmitter and IP core Tx path have completed the internal reset sequence. This signal is clocked by the cpri_clkout clock.
xcvr_reset_rx_done Output Indicates the receiver and IP core Rx path have completed the internal reset sequence. This signal is clocked by the cpri_clkout clock.
tx_analogreset_ack Output This signal rises after the TX analog reset process completes. This signal falls after you deassert the tx_analogreset signal.This signal is asynchronous. Refer to Resetting Transceiver Channels in the Arria® 10 Transceiver PHY User Guide.

This signal is available in CPRI IP cores that target an Arria® 10 device. Your custom auto-rate negotiation logic can monitor this signal to determine when it can safely begin reconfiguring the device transceiver to a new CPRI line bit rate.

rx_analogreset_ack Output This signal rises after the RX analog reset process completes. This signal falls after you deassert the rx_analogreset signal. This signal is asynchronous. Refer to Resetting Transceiver Channels in the Arria® 10 Transceiver PHY User Guide.

This signal is available in CPRI IP cores that target an Arria® 10 device. Your custom auto-rate negotiation logic can monitor this signal to determine when it can safely begin reconfiguring the device transceiver to a new CPRI line bit rate.

Related Information
Level Two Title