Stratix® 10 General Purpose I/O User Guide

Download PDF
ID 683518
Date 10/07/2024
Public
Document Table of Contents
Document Table of Contents x
1. Stratix® 10 I/O Overview 2. Stratix® 10 I/O Architecture and Features 3. Stratix® 10 I/O Design Considerations 4. Stratix® 10 I/O Implementation Guides 5. GPIO Intel® FPGA IP Reference 6. Document Revision History for the Stratix® 10 General Purpose I/O User Guide
1. Stratix® 10 I/O Overview x
1.1. Stratix® 10 I/O and Differential I/O Buffers 1.2. Stratix® 10 I/O Migration Support
2. Stratix® 10 I/O Architecture and Features x
2.1. I/O Standards and Voltage Levels in Stratix® 10 Devices 2.2. I/O Element Structure in Stratix® 10 Devices 2.3. Programmable IOE Features in Stratix® 10 Devices 2.4. On-Chip I/O Termination in Stratix® 10 Devices 2.5. External I/O Termination for Stratix® 10 Devices
2.1. I/O Standards and Voltage Levels in Stratix® 10 Devices x
2.1.1. Stratix® 10 I/O Standards Support 2.1.2. Stratix® 10 I/O Standards Voltage Support
2.2. I/O Element Structure in Stratix® 10 Devices x
2.2.1. I/O Bank Architecture in Stratix® 10 Devices 2.2.2. I/O Buffer and Registers in Stratix® 10 Devices
2.3. Programmable IOE Features in Stratix® 10 Devices x
2.3.1. Programmable Output Slew Rate Control 2.3.2. Programmable IOE Delay 2.3.3. Programmable Open-Drain Output 2.3.4. Programmable Bus Hold 2.3.5. Programmable Pull-Up Resistor 2.3.6. Programmable Pre-Emphasis 2.3.7. Programmable Differential Output Voltage 2.3.8. Programmable Current Strength
2.4. On-Chip I/O Termination in Stratix® 10 Devices x
2.4.1. RS OCT without Calibration in Stratix® 10 Devices 2.4.2. RS OCT with Calibration in Stratix® 10 Devices 2.4.3. RT OCT with Calibration in Stratix® 10 Devices 2.4.4. Dynamic OCT 2.4.5. Differential Input RD OCT 2.4.6. OCT Calibration Block in Stratix® 10 Devices
2.5. External I/O Termination for Stratix® 10 Devices x
2.5.1. Single-Ended I/O Termination 2.5.2. Differential I/O Termination for Stratix® 10 Devices
2.5.2. Differential I/O Termination for Stratix® 10 Devices x
2.5.2.1. Differential HSTL, SSTL, HSUL, and POD Termination 2.5.2.2. LVDS, RSDS, and Mini-LVDS Termination 2.5.2.3. LVPECL Termination
3. Stratix® 10 I/O Design Considerations x
3.1. Guideline: VREF Sources and VREF Pins 3.2. Guideline: Observe Device Absolute Maximum Rating for 3.0 V Interfacing 3.3. Guideline: Voltage-Referenced and Non-Voltage Referenced I/O Standards 3.4. Guideline: Do Not Drive I/O Pins During Power Sequencing 3.5. Guideline: Stratix® 10 I/O Buffer During Power Up, Configuration, and Power Down 3.6. Guideline: Maximum DC Current Restrictions 3.7. Guideline: Use Only One Voltage for All 3 V I/O Banks 3.8. Guideline: I/O Standards Limitation for Stratix® 10 TX 400 3.9. Guideline: I/O Standards Limitation for Stratix® 10 GX 400 and SX 400
4. Stratix® 10 I/O Implementation Guides x
4.1. GPIO Intel® FPGA IP 4.2. Verifying Resource Utilization and Design Performance 4.3. GPIO Intel® FPGA IP Timing 4.4. GPIO Intel® FPGA IP Design Examples 4.5. Verifying Pin Migration Compatibility 4.6. IP Migration to the GPIO IP Core
4.1. GPIO Intel® FPGA IP x
4.1.1. Release Information for GPIO Intel® FPGA IP 4.1.2. GPIO Intel® FPGA IP Data Paths 4.1.3. Register Packing
4.1.2. GPIO Intel® FPGA IP Data Paths x
4.1.2.1. Input Path 4.1.2.2. Output and Output Enable Paths
4.3. GPIO Intel® FPGA IP Timing x
4.3.1. Timing Components 4.3.2. Delay Elements 4.3.3. Timing Analysis 4.3.4. Timing Closure Guidelines
4.3.3. Timing Analysis x
4.3.3.1. Single Data Rate Input Register 4.3.3.2. Full-Rate or Half-Rate DDIO Input Register 4.3.3.3. Single Data Rate Output Register 4.3.3.4. Full-Rate or Half-Rate DDIO Output Register
4.4. GPIO Intel® FPGA IP Design Examples x
4.4.1. GPIO Intel® FPGA IP Synthesizable Quartus® Prime Design Example 4.4.2. GPIO Intel® FPGA IP Simulation Design Example
4.6. IP Migration to the GPIO IP Core x
4.6.1. Migrating Your ALTDDIO_IN, ALTDDIO_OUT, ALTDDIO_BIDIR, and ALTIOBUF IP Cores 4.6.2. Guideline: Swap datain_h and datain_l Ports in Migrated IP
5. GPIO Intel® FPGA IP Reference x
5.1. GPIO Intel® FPGA IP Parameter Settings 5.2. GPIO Intel® FPGA IP Interface Signals
5.2. GPIO Intel® FPGA IP Interface Signals x
5.2.1. Shared Signals 5.2.2. Data Bit-Order for Data Interface 5.2.3. Data Interface Signals and Corresponding Clocks
1. Stratix® 10 I/O Overview
2. Stratix® 10 I/O Architecture and Features
3. Stratix® 10 I/O Design Considerations
4. Stratix® 10 I/O Implementation Guides
5. GPIO Intel® FPGA IP Reference
6. Document Revision History for the Stratix® 10 General Purpose I/O User Guide

2.4.6. OCT Calibration Block in Stratix® 10 Devices

You can calibrate the OCT using the OCT calibration block available in each I/O bank.

You can use RS and RT OCT in the same I/O bank for different I/O standards if the I/O standards use the same VCCIO supply voltage. You cannot configure the RS OCT and the programmable current strength for the same I/O buffer.

The OCT calibration process uses the RZQ pin that is available in every calibration block in a given I/O bank for series- and parallel-calibrated termination:

  • Each OCT calibration block has an external 240 Ω reference resistor associated with it through the RZQ pin.
  • Connect the RZQ pin to GND through an external 100 Ω or 240 Ω resistor (depending on the RS or RT OCT value).
  • The RZQ pin shares the same VCCIO supply voltage with the I/O bank where the pin is located.
  • The RZQ pin is a dual-purpose I/O pin and functions as a general purpose I/O pin if you do not use the calibration circuit.

Stratix® 10 devices support calibrated RS and calibrated RT OCT on all LVDS I/O pins except for dedicated configuration pins.

Level Two Title