write_content_to_memory (::quartus::insystem_memory_edit)

The following table displays information for the write_content_to_memory Tcl command:

Tcl Package and Version

Belongs to ::quartus::insystem_memory_edit 1.0

Syntax write_content_to_memory [-h | -help] [-long_help] -content <content string> [-content_in_hex] -instance_index <instance index> -start_address <starting address> [-timeout <timeout> ] -word_count <word count>
Arguments -h | -help Short help
-long_help Long help with examples and possible return values
-content <content string> A string that represents all word values concatenated together in order in either binary or hexadecimal format
-content_in_hex The memory content string is represented in hexadecimal format
-instance_index <instance index> Index of the editable memory instance to modify
-start_address <starting address> The lowest memory address to be modified
-timeout <timeout> amount of time in milliseconds allocated before write times out. Defaults to 10 seconds
-word_count <word count> The number of contiguous memory words to be modified
		Writes the data represented in the bit stream into the
specified editable memory instance starting from the
specified address. It returns the number of successful writes. 

The bit stream should be ordered by word from high
address to low address, contiguously without gaps or
delimiters. If the starting address is ADDR, and word
count is N, the order is <word @ ADDR + N - 1>
... <word @ ADDR + 1><word @ ADDR> In each word, the
MSB is on the left, LSB is on the right. The bit
stream can be in either binary or hexadecimal. For
example, if the word width is 8, and two words, 1 and
128, are written to address 0 and 1 respectively, the
bitstream should be "1000000000000001" in binary or
"8001" in hexadecimal. The TCL command is
write_content_to_memory -instance_index 0
-start_address 0 -word_count 2 -content
"1000000000000001" or write_content_to_memory
-instance_index 0 -start_address 0 -word_count 2
-content "8001" -content_in_hex 
Example Usage
# Instance 0 is configured as {0 1024 8 RW ROM/RAM mem0}

# Initiate a editing sequence
begin_memory_edit -hardware_name "USB-Blaster \[USB-0\]" -device_name "@1: EP1S25/_HARDCOPY_FPGA_PROTOTYPE (0x020030DD)"

# Write memory content using binary string
write_content_to_memory -instance_index 0 -start_address 575 -word_count 2 -content "0000001011011100" -timeout 30000

# Read back memory content in binary string written 
puts [read_content_from_memory -instance_index 0 -start_address 575 -word_count 2 ]

# Write memory content using hexadecimal string
write_content_to_memory -instance_index 0 -start_address 575 -word_count 2 -content "E2F1" -content_in_hex

# Read back memory content in hexadecimal string written 
puts [read_content_from_memory -instance_index 0 -start_address 575 -word_count 2 -content_in_hex]

# End the editing sequence
Return Value Code Name Code String Return
TCL_OK 0 INFO: Operation successful
TCL_ERROR 1 ERROR: Data specified in the string does not match the number of bits to update the memory of the specified number of words.
TCL_ERROR 1 ERROR: A memory edit sequence has not been started.
TCL_ERROR 1 ERROR: The specified word count and the starting address exceeds the specified memory buffer size.
TCL_ERROR 1 ERROR: The specified editable memory instance index is invalid.
TCL_ERROR 1 ERROR: The specified editable memory instance index is invalid.
TCL_ERROR 1 ERROR: JTAG communication error is detected. It can be caused by the hardware failure or poor signal integrity in the JTAG chain.
TCL_ERROR 1 ERROR: The device is locked by another application.