Low Latency 100G Ethernet Intel® Agilex™ FPGA IP Design Example User Guide

Download PDF
ID 683315
Date 12/14/2020
Public
Document Table of Contents
Document Table of Contents x
1. Quick Start Guide 2. Design Example Description 3. Document Revision History for the Low Latency 100G Ethernet Intel Agilex FPGA IP Design Example User Guide
1. Quick Start Guide x
1.1. Generating the Design Example 1.2. Directory Structure 1.3. Simulating the Design Example Testbench 1.4. Compiling the Compilation-Only Project 1.5. Compiling and Configuring the Design Example in Hardware 1.6. Testing the Low Latency 100G Ethernet Intel Agilex FPGA Intel® FPGA IP Design in Hardware
1.1. Generating the Design Example x
1.1.1. Design Example Parameters
1.6. Testing the Low Latency 100G Ethernet Intel Agilex FPGA Intel® FPGA IP Design in Hardware x
1.6.1. Testing the Hardware Design Example using Ethernet Toolkit
2. Design Example Description x
2.1. Features 2.2. Hardware and Software Requirements 2.3. Simulation 2.4. Design Example Behavior 2.5. Design Example Registers 2.6. Design Example Interface Signals
2.5. Design Example Registers x
2.5.1. Packet Generator Programming Sequence
1. Quick Start Guide
2. Design Example Description
3. Document Revision History for the Low Latency 100G Ethernet Intel Agilex FPGA IP Design Example User Guide

2.5. Design Example Registers

Table 5.   Low Latency 100G Ethernet Intel Agilex FPGA Hardware Design Example Register MapLists the memory mapped register ranges for the hardware design example. You access these registers with the reg_read and reg_write functions in the System Console.
Word Offset Register Type
0x0000 KR4 registers
0x0300 PHY registers
0x0400 TX MAC registers
0x0500 RX MAC registers
0x0800 TX Statistics Counter registers
0x0900 RX Statistics Counter registers
0x1000 Packet Client registers
0x4000 PMA registers 1
Table 6.  Packet Client Registers You can customize the Low Latency 100G Ethernet Intel Agilex FPGA hardware design example by programming the packet client registers.

Addr

Name

Bit

Description

HW Reset Value

Access

0x1000 PKT_CL_SCRATCH [31:0] Scratch register available for testing. RW
0x1001 PKT_CL_CLNT [31:0] Four characters of IP block identification string "CLNT" RO
0x1008 Packet Size Configure [29:0] Specify the transmit packet size in bytes. These bits have dependencies to PKT_GEN_TX_CTRL register.
  • Bit [29:16]: Specify the upper limit of the packet size in bytes. This is only applicable to incremental mode.
  • Bit [13:0]:
    • For fixed mode, these bits specify the transmit packet size in bytes.
    • For incremental mode, these bits specify the lower limit of the transmit packet size in bytes.
0x25800040 RW
0x1009 Packet Number Control [31:0] Specify the number of packets to transmit from the packet generator. These bits have dependencies to PKT_GEN_TX_CTRL register.
  • Bit [31]:
    • 1: For fixed/incremental mode with fixed number of packets, this is the number of packets enable bit.
    • 0: For random mode or fixed/incremental mode without fixed number of packets.
  • Bits [30:0]:
    • If bit [31] is set, specifies the number of packets to be sent by the packet generator.

For more information, refer to the Packet Generator Programming Sequence.

0xA RW
0x1010 PKT_GEN_TX_CTRL [7:0]
  • Bit [0]: Reserved.
  • Bit [1]: Packet generator status control bit.
    • 0: Packet generator starts sending out the packets.
    • 1: Packet generator stops sending out the packets.
  • Bit [2]: Reserved.
  • Bit [3]: Has the value of 1 if the IP core is in MAC loopback mode; has the value of 0 if the packet client uses the packet generator.
  • Bit [5:4]:
    • 00: Random mode
    • 01: Fixed mode
    • 10: Incremental mode
  • Bit [6]:
    • 1: For transmission without gap in between packets.
    • 0: For transmission with random gap in between packets.
  • Bit [7]: Reserved.
0x6 RW
0x1011 Destination address lower 32 bits [31:0] Destination address (lower 32 bits) 0x56780ADD RW
0x1012 Destination address upper 16 bits [15:0] Destination address (upper 16 bits) 0x1234 RW
0x1013 Source address lower 32 bits [31:0] Source address (lower 32 bits) 0x43210ADD RW
0x1014 Source address upper 16 bits [15:0] Source address (upper 16 bits) 0x8765 RW
0x1016 PKT_CL_LOOPBACK_RESET [0] MAC loopback reset. Set to the value of 1 to reset the design example MAC loopback. 1'b0 RW

Section Content
Packet Generator Programming Sequence

Related Information
1 Each PHY channel has its PMA registers set. PMA registers sets are offset from each other by 0x800 channel offset, starting at the 0x4000 word offset.
Level Two Title