• 2019 Update 4
  • 03/20/2019
  • Public Content

__local Memory

Local memory can be used to avoid multiple redundant reads from and writes to global memory. But it is important to note that the SLM (which is used to implement local memory), occupies the same place in the architecture as the L3 cache. So the performance of local memory accesses is often similar to that of a cache hit. Using local memory is typically only advantageous when the access pattern favors the banked nature of the SLM array.
When local memory is used to store temporary inputs and/or outputs, there are a few things to consider:
  • When reading multiple items repeatedly from global memory:
    • You can benefit from prefetching global memory blocks into local memory once, incurring a local memory fence, and reading repeatedly from local memory instead.
    • Do not use single work-item (like the one with local id of 0) to load many global data items into the local memory by using a loop. Looped memory accesses are slow, and some items might be prefetched more than once.
    • Instead, designate work-items to prefetch a single global memory item each, and then incur a local memory fence, so that the local memory is full.
  • When using local memory to reduce memory writes:
    • Enable a single work-item to write to an independent area of local memory space, and do not enable overlapping write operations.
    • If, for example, each work-item is writing to a row of pixels, the local memory size equals the number of local memory items times the size of a row, and each work-item indexes into its respective local memory buffer.
As we discussed earlier to optimize performance when accessing
memory, a kernel must minimize the number of bank conflicts. As long as each work-item accesses
memory with an address in a unique bank, the access occurs at full bandwidth. Work-items can read from the same address within a bank with no penalty, but writing to different addresses within the same bank produces a bank conflict and impacts performance.
To see how bank conflicts can occur, consider the following examples (assume a “row” work-group, <16, 1, 1>):
__local int* myArray = ...; int x; x = myArray[ get_global_id(0) ]; // case 1 x = myArray[ get_global_id(0) + 1 ]; // case 2 x = myArray[ get_global_size(0) – 1 – get_global_id(0) ]; // case 3 x = myArray[ get_global_id(0) & ~1 ]; // case 4 x = myArray[ get_global_id(0) * 2 ]; // case 5 x = myArray[ get_global_id(0) * 16 ]; // case 6 x = myArray[ get_global_id(0) * 17 ]; // case 7
Cases 1, 2, and 3 access sixteen unique banks and therefore achieve full memory bandwidth. If you use global memory array instead of a local memory array, case 2 does not achieve full bandwidth due to accesses to two cache lines. The diagram below shows case 2.
Case 4 reads from 8 unique banks, but with the same address for each bank, so it should also achieve full bandwidth.
Case 5 reads from eight unique banks with a different address for each work-item, and therefore should achieve half of the bandwidth of Case 1.
Case 6 represents a worst-case for local memory: it reads from a single bank with a different address for each work-item. It should operate at 1/16th the memory performance of Case 1.
Case 7 is a stridden case similar to Case 6, but since it reads from 16 unique banks, this case also achieves full bandwidth.
The difference between Case 6 and Case 7 is important because this pattern is frequently used to access “columns” of data from a two-dimensional local memory array. Choose an array stride that avoids bank conflicts when accessing two-dimensional data from a local memory array, even if it results in a “wasted” column of data. For example, Case 7 has stride of 17 elements in compare to 16 elements in Case 6.

Product and Performance Information


Performance varies by use, configuration and other factors. Learn more at www.Intel.com/PerformanceIndex.