This document contains instructions for installing the TokenExpress™ adapter driver. It contains information specific to the installation and operation of Intel's TokenExpress™ adapters only. Please refer to the appropriate Network Operation System documentation for any NOS-specific questions or other information.

Installing the remote boot PROM on the TokenExpress adapter:

1. Follow the instructions in the manual that shipped with the remote boot PROM.

2. Be careful to position the boot PROM correctly on the TokenExpress adapter. After you have installed the boot PROM, make sure none of the pins were bent.

3. Be aware of the Page Frame address, and the memory addresses of other boards in your system before setting the RPL address location.

1. Configure the server so your workstation can boot from the network. You will need the TokenExpress adapter driver diskette and the installation manual for your version of NetWare to set up the server. Insert the following line in the file server's AUTOEXEC.NCF file:
   load TOKENRPL

   The following is a typical AUTOEXEC.NCF file:

   file server name TR_TEST
   ipx internal net 63965
   load c:\netware\octok161 slot=2 frame=TOKEN-RING name=seg1
   bind ipx to seg1 net=100
   load c:\netware\octok161 slot=2 frame=TOKEN-RING_SNAP name=seg2
   bind ipx to seg2 net=200
   load TOKENRPL
   load route <----- (Optional if using Source Routing)
   set allow unencrypted passwords=ON

2. Create a bootable floppy disk. Copy the following files from the NetWare WSGEN diskette to the bootable floppy disk:
   LSL.COM
   RPLODI.COM
   ROUTE.COM (Optional, if using Source Routing)
   IPXODI.COM
   NETX.EXE

   NOTE: The latest files are available from Novell ^†.

3. Copy the following file from the TokenExpress adapter driver diskette #1 to the bootable floppy diskette:
   OCTOK16.COM

4. Create an AUTOEXEC.BAT file on the bootable floppy disk which contains the following lines:
   prompt $p$g
   lsl
   rplodi
   octok16
   route (Optional if using Source Routing)
   ipxodi
   netx

5. Create a generic CONFIG.SYS file on the bootable floppy disk like the one that was used during testing:
   files=50
   buffers=25

6. Without re-booting, from A:, type the following:
   lsl
   octok16
   route (Optional if using Source Routing)
   ipxodi
   netx
   f:

7. Login as SUPERVISOR to the server onto which you will build the DOS Remote Boot image.

8. At the F:\LOGIN prompt, type the following:
   f:\system\dosgen <ENTER>

9. At this point, all files on the bootable diskette in drive A: will be read and a boot image file will be created in the \LOGIN directory of the server you are currently logged into. The name of this file will be NET$DOS.SYS.

10. Copy the AUTOEXEC.BAT file from the disk in drive A: to the F:\LOGIN directory.

    NOTE: If you forget this step, you will receive a "Batch file missing" error during the remote boot process.

11. Remove the bootable floppy diskette in the A: drive and re-boot the workstation. The following screen will be displayed:
    Intel TokenExpress™ FLASH RPL PROM for Novell & MS/IBM v1.12

    Booting in 10 seconds with configuration:

    Source : Local Disk

    Press any key to change settings...

12. Hit any key and the following screen appears:
    Intel TokenExpress™ FLASH RPL PROM for Novell & MS/IBM v1.12

    Messages: Boot Delay: Source:

    Extended 10 Local Disk

    Use up and down arrows to move, left arrow to adjust, ESC to continue.

13. Using the arrow keys, change the settings so that:

    Source = Novell Network and Server = Name of the server which contains the Boot Image.

    The screen should now look like this:

    Intel TokenExpress™ FLASH RPL PROM for Novell & MS/IBM v1.12

    Messages: Boot Delay: Source: Node: Server:

    Extended 10 Novell Network 005500nnnnnn Your Remote Boot Server

    Use up and down arrows to move, left arrow to adjust, ESC to continue.

14. Press ESC to continue, then type "y" to make the changes permanent.

15. Once the workstation boots and attaches to the server, you may log into the network.

This applies to:

TokenExpress™ 16/p Adapter