This installation document applies to the TokenExpress™ 16/p LAN Adapter software release v7.0 which is available in the archive TE16DISK.EXE.

Location of Driver: \NETWARE\TE16.LAN

General Installation

1. From the Novell* IntranetWare Client software, run INSTALL.EXE from DOS.
   

2. Select the Novell* IntranetWare Client products you want to install on your workstation from the list:

   [X] NetWare* Client 32 for DOS
   [X] NetWare Client 32 for Windows
   [  ] NetWare TCP/IP protocol stack
   [  ] NetWare IP (TCP/IP Required)
   [  ] Desktop SNMP
   [  ] HOSTMIB for SNMP (SNMP Required)
   [  ] NetWare TSA for SMS
   

   Note: "NetWare Client 32 for DOS" and "NetWare Client 32 for Windows" are usually selected by default.
   

3. From the Customize Support for Windows* menu, specify if you want to use multiple country codes or if you want to set the shared Windows path. The default for both of these is NO.
   

4. From the Select LAN Driver Type menu, select "32-bit LAN drivers".
   

5. From the 32-Bit Network Board Drivers menu, select "USER SPECIFIED 32 BIT DRIVER".
   

6. From the Insert Driver Disk window, specify the driver path as "javascript:void(null);". Then select the "Intel TokenExpress^TM Adapters" from the 32-Bit Network Board Drivers window.

7. Specify the settings for the Intel TokenExpress LAN adapter:
   
   

   Parameter	Default
   Frame Type	FRAME TOKEN-RING MSB
   Info message control	SHOWINFO 0
   Node Address

8. From the Installation Configuration Summary, verify the default settings for Novell IntranetWare Client are correct, or modify as necessary.
   Modify AUTOEXEC.BAT and CONFIG.SYS [YES]
   

   Client Directory:	C:\NOVELL\CLIENT32
   Windows Directory:	C:\WINDOWS
   LAN driver type:	32-bit LAN drivers
   LAN driver:	Intel TokenExpressTM Adapters

9. Novell* IntranetWare Client will now copy the files to your workstations and modify the configuration files to match your selected configuration.
   
   

1. Check for a LASTDRIVE statement in the CONFIG.SYS file. You must have LASTDRIVE=Z in config.sys when using Novell's Client 32.
   

2. Verify that you have FIRST NETWORK DRIVE = F in the NET.CFG file under the NetWare DOS Requester section.

   NOTE: NET.CFG is position sensitive, so be careful to indent lines with one space or one tab as shown above in the example.
   

3. Verify that the TokenExpress™ adapter passes the diagnostics test by running TE16DIAG.EXE on the TokenExpress driver disk and selecting "Test Adapter". If the adapter fails diagnostics it will not function correctly running Novell IntranetWare Client.
   Sample Configurations
   Below are sample files from a Novell* IntranetWare Client workstation with a TokenExpress adapter installed using the default installation:
   

   CONFIG.SYS
   DEVICE=C:\WINDOWS\HIMEM.SYS
   BUFFERS=30,0
   FILES=60
   LASTDRIVE=Z
   
   

   AUTOEXEC.BAT
   prompt $P$G
   path=C:\WINDOWS;c:\dos;C:\NOVELL\CLIENT32\
   SET TEMP=C:\TEMP
   @CALL C:\NOVELL\CLIENT32\STARTNET
   

   STARTNET.BAT
   SET NWLANGUAGE=ENGLISH
   C:\NOVELL\CLIENT32\NIOS.EXE
   LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
   LOAD C:\NOVELL\CLIENT32\CMSM.NLM
   LOAD C:\NOVELL\CLIENT32\TOKENTSM.NLM
   LOAD C:\NOVELL\CLIENT32\TE16.LAN PORT=A40 FRAME=TOKEN-RING MSB
   LOAD C:\NOVELL\CLIENT32\TE16.LAN PORT=A40 FRAME=TOKEN-RING_SNAP MSB
   LOAD C:\NOVELL\CLIENT32\IPX.NLM
   LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM

   NET.CFG
   NetWare DOS Requester
   FIRST NETWORK DRIVE F
   NETWARE PROTOCOL NDS BIND
   Protocol IPX
   IPX SOCKETS 40

This applies to:

TokenExpress™ 16/p Adapter TokenExpress™ EISA 16/4 Adapter TokenExpress™ EISA 32 Adapter TokenExpress™ MCA Adapter